Friday, April 18, 2014
How to Remove a Fuel Pump Cover
You will need to remove the fuel pump cover if you are cleaning the fuel pump, the fuel pump filter or the fuel tank strainer on your vehicle. These parts are cleaned when you are troubleshooting a vehicle that is experiencing inadequate fuel pressure or a fuel leak. Not all vehicles have a fuel pump cover, but if yours does, removing the cover is a fairly straightforward job requiring a few basic tools.
Instructions
- 1
Disconnect the negative (black) cable from the battery.
2Raise the vehicle with a car jack to allow you easy access underneath.
3Locate the fuel pump cover on the bottom side of fuel tank, under the vehicle.
4Remove the bolt from the strap holding down the fuel cover, using a 13 mm wrench. The bolt is usually located near the wheel well.
5Pull the fuel cover from the fuel tank. It will come off easily once the strap is removed.
Monday, March 10, 2014
How to Glue Down a New Vinyl Dash Cover
New vinyl dashboard covers give your car a new look, and are a simple way to add style. Some vinyl covers require you to remove certain components of the dashboard to complete the installation, but most only need a small amount of adhesive to keep it fastened securely in place. Vinyl covers must be positioned caully to ensure a proper fit. Avoid using too much glue as this will unnecessarily prolong the drying time and may leave bumps underneath the finished cover.
Instructions
- 1
Wash your cars dashboard thoroughly before applying the adhesive. Spray the dashboard with vinyl cleaner, buff the dashboard with a moist paper towel and wipe away any excess. Dry completely with a lint-free towel or cloth.
2Line up the dash cover with your cars features caully. Once the glue sets it is very difficult to reposition your vinyl dash cover, so you will want to get it right the first time. Use a pencil to mark any areas that need to be cut or altered. Caully cut out these areas, laying the vinyl cover back on the dashboard occasionally to ensure a good fit.
3Spray a thin layer of glue on the bottom of the cover and on the top of your dashboard. Let it dry for one minute (this will make the glue very tacky and will adhere to the dashboard more easily).
4Lay the cover down on the dashboard. Go slowly and rub areas as you go along to ensure there are no air pockets. Check every five or six hours to ensure that the vinyl glue is setting correctly. Add a small amount of glue to any edges that fray up, and apply firm pressure to set. Keep vinyl dash cover dry and out of direct sunlight for twenty-four hours following installation.
Saturday, November 23, 2013
How to Change a 2000 Chevrolet S10 2 2L Valve Cover Gasket
Changing the valve cover gasket on a 2000 Chevy S10 2.2L requires some mechanical skill, as there are a few components that need to be removed in order to reach that gasket. However, with the right tools and some patience, the do-it-yourself repair is well worth the effort, because it will save a lot of money. The job is somewhat labor-intensive, which makes it costly at repair shops. The new gasket is inexpensive and easy-to-find, most auto parts stores should have one in stock for a model as common as the 2000 Chevy S10 2.2L
Instructions
- 1
Let the engine cool completely.
2Remove black plastic air duct on the left side of the engine by separating it from the intake hose. In most S10 models built between 1998 and 2003, including the 2.2L version, you need to loosen a few clamps with a screwdriver to pull the air duct off the hose. In some models, the air duct is just stuck on the hose and comes off when you pull hard enough.
3Locate the throttle to the left off the valve cover. Pull the cable to unsnap it from the bracket.
4Pull the brake booster hose from its point on top of the valve cover.
5Remove the valve cover bolts by using the ratchet, the extension and the socket set. There should be eight No. 10 bolts.
6Take off the valve and scrape out the old gasket, which most likely will be hard from wear. Make sure no residue of the old gasket is in the mold. Clean the mold with a rag and wipe off gunk and dirt that might be stuck.
7Place the new gasket in the mold, making sure it fits tightly. Reassemble the other components in the same order you disassembled them.
